IZE学院 订单查询

0086-21-31006702 联系我们 关于我们 账号注册及登录EN
您当前的位置: 首页 >> 产品中心 >> 液压 >> 液压阀 >> 液压平衡阀 >> OLEOWEB阀VBCF系列

OLEOWEB阀VBCF系列

请注意:照片可能并不是实际产品,具体请参阅标题和产品规格及所有细节描述。
产品品牌:
型号:VBCF120
OLEOWEB阀VBCF系列 VBCF120
预估货期:
关  键  词:OLEOWEBVBCF系列VBCF120VBCF1202S
相似产品:
是否有问题?联系我们工作人员
  邮件联系

OLEOWEB阀VBCF120参数特性

Technical data


Mineral oil

ISO 6743/4

Oil viscosity

15-250 mm2/s

Max contamination index with filte

ISO 4406:1999 Classe 19/17/14

Oil temperature

-4°F +176°F

Ambient temperature

-4°C +122°F 

It is necessary a filter use to protect the valve (advised filtration 15 μm)

爱泽工业(ize-industries)并不是本网站所列所有产品的授权代理商或经销商。 本网站使用的所有产品名称,商标,品牌等均属于各自品牌厂家所有。 本网站在产品或图片描述中,出现具有这些名称,商标,品牌等信息的产品仅用于识别目的,并非旨在表明任何与持有者的从属及授权关系。

OLEOWEB阀VBCF系列描述说明及选型

Oleoweb VBCF平衡阀设计用于在可预见执行器(例如气缸或液压马达)上的重力的工作条件下获得最佳的负载控制。VBCF偏心阀是双作用的,即,它们在两个输送方向上都控制负载。它们是易折的阀门,因此可以直接应用在执行器上,从而减少滞后现象。承受重力载荷是平衡阀的基本任务之一。为了确保在负载保持方面的最佳性能,Oleoweb特别注意其液压密封平衡阀,用高强度钢制成零件,经过硬化和磨削,并在组装后仔细检查阀的尺寸和公差以及密封性。偏心阀的另一个主要任务是控制执行器的运动。由于先导比,可以在低于阀设定压力的压力下释放负载。对于Oleoweb平衡阀,可以提供不同的先导报告。对比弹簧还允许流体通道区域逐渐打开,从而即使在存在负载荷的情况下也可以控制执行器的运动,从而避免了气蚀的发生。为了获得最佳操作,建议设置平衡阀值比最大工作负荷高30%。使用塑料盖也可以密封设置,以防篡改。VBCF 平衡阀还可以执行防震阀的功能,保护连接到执行器的结构不受突然的压力峰值(例如,过高的负载或意外冲击)造成的损坏。为此,必须将分配器上的回流管连接到排水管。VBCF是一种无补偿平衡阀:回油管路上的任何残余压力都会通过提高打开阀门所需的设定压力和先导压力来抵消阀门的打开。因此,这种类型的阀更适合安装在带有开放式中心阀芯的分配器的下游,并用于在中性位置排放。Oleoweb VBCF 平衡阀是阀体中的零件:这些零件容纳在液压歧管中。该解决方案使您能够在保持整体尺寸不变的情况下管理高流量。阀体和外部部件均由高强度钢制成,并通过镀锌保护其免受腐蚀。六个表面上的车身加工确保了表面处理的最佳执行,并具有其有效性的优势。对于暴露于特别腐蚀性的腐蚀剂的应用(例如海洋应用),可应要求提供锌镍处理。钢制阀体允许在最高350 bar(5075 PSI)的工作压力下工作,并确保高耐磨性,从而提高了阀的可靠性和耐用性。VBCF阀的尺寸从BSPP 1/4“到BSPP 1/2”不等,流量高达60 lpm(15,9gpm)。

 

The Oleoweb VBCF counterbalance valves are designed to obtain the best control of the loads in working conditions that foresee gravitational forces on the actuators, such as cylinders or hydraulic motors. The VBCF overcenter valves are double-acting, ie they control the load in both delivery directions; they are flangable valves, which can therefore be applied directly on the actuator with consequent reduction of the hysteresis phenomenon. Sustaining a gravitational load is one of the fundamental tasks of counterbalance valves. To ensure the best performance in terms of load holding, Oleoweb takes particular care of the hydraulic seal of its counterbalance valves, making the components in high-strength steel, hardened and grinded and carefully checking dimensions and tolerances as well as the sealing of the valves once assembled. Another main task of the overcenter valves is the control of the actuator movement. Thanks to the piloting ratio, it is possible to release the load at a pressure lower than the valve setting pressure. For the Oleoweb counterbalance valves, different piloting reports are available. The contrast spring also allows a gradual opening of the fluid passage area allowing the control of the actuator movement even in the presence of negative loads and thus avoiding the onset of cavitation. For optimal operation it is advisable to set the counterbalance valve at a value 30% higher than the maximum work load. Using a plastic cap it is also possible to seal the setting, protecting it from tampering. The VBCF counterbalance valves can also perform the function of shock-proof valves, protecting the structure connected to the actuator from damage caused by sudden pressure peaks due, for example, to excessively high loads or accidental impacts. For this to be possible, the return line on the distributor must be connected to the drain. The VBCF is a non-compensated counterbalance valve: any residual pressure on the return lines counter the opening of the valve by raising the setting and pilot pressure necessary to open it. For this reason this type of valve is better suited to be installed downstream of distributors with open center spool, with uses connected to discharge in neutral position. Oleoweb VBCF counterbalance valves are parts in body valves: the components are housed inside a hydraulic manifold. This solution allows you to manage high flow rates while keeping down the overall dimensions. The valve body and external components are made of high-strength steel and are protected against corrosion by galvanizing. The processing of the body on the six faces guarantees an optimal execution of the surface treatment to the advantage of its effectiveness. For applications exposed to particularly aggressive corrosive agents (eg marine applications) the zinc-nickel treatment is available on request. The steel body allows working with operating pressures up to 350 bar (5075 PSI) and ensures a high resistance to wear to the benefit of valve reliability and durability. VBCF valves are available in sizes from BSPP 1/4 "to BSPP 1/2" for flow rates up to 60 lpm (15,9 gpm).

 

OLEOWEB阀VBCF系列选型介绍

image.png 

 

OLEOWEB阀VBCF120尺寸图

image.png 

 

OLEOWEB阀VBCF系列其他常见型号:

OLEOWEB  VBCF140

OLEOWEB  VBCF380

OLEOWEB  VBCF120

 

OLEOWEB valve NEW + ORIGINAL+ ONE YEAR WARRANTY

 

爱泽工业成立于2010年,定位于向先进制造工业提供高端制造技术和设备。代理经营世界先进的电气自动化、机械与传动、流体控制、仪器仪表、工具等产品。作为电气,液压以及气动解决方案的合作伙伴,我们利用我们的全球协作团队,为客户提供先进解决方案,市场知识以及相关增值服务来帮助优化客户的工作效率,提高可靠性和安全性,致力于成为工业产品和解决方案的优质渠道。

 

如果有任何关于OLEOWEB阀VBCF120的疑问,请随时与我们电联,(021-3100 6702),我们将尽全力解决您的问题。

 

If you have any question for OLEOWEB products, please feel free to dial 0086-21-3100 6702/ send request email to sales@ize-industries.com / browse our website: www.ize-industries.com.


OLEOWEB阀VBCF系列 VBCF120描述说明

免责声明:本网站的布局,设计和编辑版权归©上海爱泽工业设备有限公司(简称ize-industries)所有,保留所有相关权利。 Ize-industries销售工业领域的全新产品,库存产品,并不断开发渠道购买此类产品。 本网站未经所有制造商或商标授权或批准。ize-industries不是所有制造商的授权经销商,附属公司或代表处。除非另有明确说明,否则此处出现的指定商标,品牌名称和品牌均为其各自所有者的财产。